-
We need your support!
We are currently struggling to cover the operational costs of Xtremepapers, as a result we might have to shut this website down. Please donate if we have helped you and help make a difference in other students' lives!
Click here to Donate Now (View Announcement)
Physics Practical Notes
- Thread starter Oronkira
- Start date
- Messages
- 1,800
- Reaction score
- 1,800
- Points
- 173
I've posted them before, but anyway, here you go:
Okay firstly, DO NOT write about reaction time, repeat readings, micrometer, or parallax because examiners will not give marks for these errors.
Here's a link that might help you for practicals:
http://mypages.iit.edu/~rcoleman/apmanual.html
Oscillations
* Perform 3 sets of measurements for each different oscillation, (you will get more marks if you do 2 sets of repeats).
* Measure at least 30 periods in total.
* Preferably make each measurement 20 periods long.
* Precaution: minimize oscillations in any other plane other than the one being observed
* Always write times to two d.p., never to the nearest second.
* Precaution: do small amplitude oscillations
* Precaution: say that you did several periods at once to minimize reaction time errors.
Moments
* Precaution: balance the ruler being used first.
* Use distances from the pivot of greater than 25 cm (250 mm).
* Weigh the unknown and known masses in your hands before using the ruler, and place the lighter mass as far from the pivot as possible.
* Measure distances from the pivot to the centre of mass of the object.
* All measurements should be to 1 mm accuracy.
* To make sure the rule is balanced, pull each end down. If it comes up again then the rule must have equal moments acting on it on either end.
Density Measurements
* When using a micrometer, one full rotation of the barrel is 0.5 mm (50 on the barrel scale).
* The micrometer reads to 0.01 mm accuracy.
* Vernier calipers can read to 0.05 mm accuracy. However, it is advisable to quote the figure to 0.1 mm accuracy, as this will give a larger uncertainty, which will make comparisons in later parts of the question easier.
* If measuring a very small dimension, measure several "thicknesses" of it. Remember to divide by the number of thicknesses after the measurement!
* Precaution: check the zero error on the micrometer and/or Vernier calipers. Wipe the jaws of the micrometer to remove grease.
* Give answers to 2 or 3 s.f. : it is meaningless to write, for example, "density is 7785.654 kg m-3"!
* Always take at least 3 readings for each measurement, and take an average.
* When measuring string diameters or foil thicknesses (or similar), use a minimum of 10 thicknesses.
Uncertainties
* % Uncertainty =
* When multiplying or dividing quantities, add their % uncertainties together.
* When adding or subtracting quantities, add their absolute errors together, then divide by the result of the addition/subtraction of the measurement, e.g. for , where , and , the absolute errors added = 0.102 mm. Therefore the % uncertainty is:
* If you have to calculate the error in, e.g. , the absolute error in d must be multiplied by pi and then added to the absolute error in x. The percentage uncertainty is this total error divided by the calculated and the result multiplied by 100.
* If a measurement is to be raised to a power, then multiply the % uncertainty in the measurement by the power to get the % uncertainty in the overall term.
* If two values, for say, a density are available, calculate the % difference between them. If a value is given by the examiner, then use this as the "correct" value, and calculate the % difference the following way: where x is your measured value, and c is the examiner's value. If you have obtained two values, then the expression changes: where x1 and x2 are your measured values, and is the median of the two, (not necessarily the mean!).
* Compare the % difference with your % uncertainty. Any relationship suggested, such as that the two densities should be equal, can be considered correct if your % difference is less than your % uncertainty. This will gain you marks!
* If your % uncertainties look small, check that you have multiplied by 100!
Electrical Experiments
* With capacitor discharges, either take readings every 5 seconds for the first part of the discharge, or I think that every 10 seconds is sufficient.
* If a range is specified over which you should take measurements, do not exceed it: you will be penalised.
* With an analogue ammeter, use the top scale. This reads (generally), from 20, to 0, to 10. These are in fact divisions of 10 m A, and the meter actually reads from -20 to 100 m A. If you are out by a factor of 10, (e.g. you get a calculated cell voltage of 0.15 V), check that you have read the meter correctly. Always remember that the polarity on the meter must be correct.
* Any small discrepancy in your results can be explained by "electrical resistance at the contacts in the circuit".
* With most electrical experiment where a curve will be obtained (e.g. the V/I characteristic of a diode), 9 points on a smooth curve are sufficient.
Graphs
* With any graph, a minimum of 6 to 8 points are needed, and you must have at least 4 points on a curve.
* When measuring the gradient of a graph, carry your tangent on to the sides of the graph paper, however big your graph. The triangle you use should be greater than 10 cm in length and height, although in some mark schemes 100 cm2 is fine.
* Your graph does not have to go through the origin. If the data does not indicate that it does so, do not force it to. Comment on the fact that there must have been a systematic error.
* When choosing values to read of a graph, it is better to take them from the middle part of the curve, as this is where you will have more points per change in y co-ordinate.
* When describing your "plan" in Experiment C, state that the graph you plot will be a straight line through the origin (if this is the case!), of gradient = to an expression which will help you confirm the relationship suggested by the examiner.
* Turning points on graphs require at least 4 points.
* If points near the origin deviate substantially from your line of best fit, point out that for small measurements there is a greater uncertainty.
Experiments Involving Temperature
* Readings should be accurate to fractions of a degree.
* Stir any liquid being heated.
* Insulate the apparatus if possible.
* The thermometer should not be touching the sides of the container it is in, and should be in the middle of the liquid you are measuring the temperature of.
* Precaution: read the thermometer at eye level to avoid parallax error.
* The bulb of the thermometer should be completely submerged.
* Comment on the result obtained being the right order of magnitude.
Okay firstly, DO NOT write about reaction time, repeat readings, micrometer, or parallax because examiners will not give marks for these errors.
Here's a link that might help you for practicals:
http://mypages.iit.edu/~rcoleman/apmanual.html
Oscillations
* Perform 3 sets of measurements for each different oscillation, (you will get more marks if you do 2 sets of repeats).
* Measure at least 30 periods in total.
* Preferably make each measurement 20 periods long.
* Precaution: minimize oscillations in any other plane other than the one being observed
* Always write times to two d.p., never to the nearest second.
* Precaution: do small amplitude oscillations
* Precaution: say that you did several periods at once to minimize reaction time errors.
Moments
* Precaution: balance the ruler being used first.
* Use distances from the pivot of greater than 25 cm (250 mm).
* Weigh the unknown and known masses in your hands before using the ruler, and place the lighter mass as far from the pivot as possible.
* Measure distances from the pivot to the centre of mass of the object.
* All measurements should be to 1 mm accuracy.
* To make sure the rule is balanced, pull each end down. If it comes up again then the rule must have equal moments acting on it on either end.
Density Measurements
* When using a micrometer, one full rotation of the barrel is 0.5 mm (50 on the barrel scale).
* The micrometer reads to 0.01 mm accuracy.
* Vernier calipers can read to 0.05 mm accuracy. However, it is advisable to quote the figure to 0.1 mm accuracy, as this will give a larger uncertainty, which will make comparisons in later parts of the question easier.
* If measuring a very small dimension, measure several "thicknesses" of it. Remember to divide by the number of thicknesses after the measurement!
* Precaution: check the zero error on the micrometer and/or Vernier calipers. Wipe the jaws of the micrometer to remove grease.
* Give answers to 2 or 3 s.f. : it is meaningless to write, for example, "density is 7785.654 kg m-3"!
* Always take at least 3 readings for each measurement, and take an average.
* When measuring string diameters or foil thicknesses (or similar), use a minimum of 10 thicknesses.
Uncertainties
* % Uncertainty =
* When multiplying or dividing quantities, add their % uncertainties together.
* When adding or subtracting quantities, add their absolute errors together, then divide by the result of the addition/subtraction of the measurement, e.g. for , where , and , the absolute errors added = 0.102 mm. Therefore the % uncertainty is:
* If you have to calculate the error in, e.g. , the absolute error in d must be multiplied by pi and then added to the absolute error in x. The percentage uncertainty is this total error divided by the calculated and the result multiplied by 100.
* If a measurement is to be raised to a power, then multiply the % uncertainty in the measurement by the power to get the % uncertainty in the overall term.
* If two values, for say, a density are available, calculate the % difference between them. If a value is given by the examiner, then use this as the "correct" value, and calculate the % difference the following way: where x is your measured value, and c is the examiner's value. If you have obtained two values, then the expression changes: where x1 and x2 are your measured values, and is the median of the two, (not necessarily the mean!).
* Compare the % difference with your % uncertainty. Any relationship suggested, such as that the two densities should be equal, can be considered correct if your % difference is less than your % uncertainty. This will gain you marks!
* If your % uncertainties look small, check that you have multiplied by 100!
Electrical Experiments
* With capacitor discharges, either take readings every 5 seconds for the first part of the discharge, or I think that every 10 seconds is sufficient.
* If a range is specified over which you should take measurements, do not exceed it: you will be penalised.
* With an analogue ammeter, use the top scale. This reads (generally), from 20, to 0, to 10. These are in fact divisions of 10 m A, and the meter actually reads from -20 to 100 m A. If you are out by a factor of 10, (e.g. you get a calculated cell voltage of 0.15 V), check that you have read the meter correctly. Always remember that the polarity on the meter must be correct.
* Any small discrepancy in your results can be explained by "electrical resistance at the contacts in the circuit".
* With most electrical experiment where a curve will be obtained (e.g. the V/I characteristic of a diode), 9 points on a smooth curve are sufficient.
Graphs
* With any graph, a minimum of 6 to 8 points are needed, and you must have at least 4 points on a curve.
* When measuring the gradient of a graph, carry your tangent on to the sides of the graph paper, however big your graph. The triangle you use should be greater than 10 cm in length and height, although in some mark schemes 100 cm2 is fine.
* Your graph does not have to go through the origin. If the data does not indicate that it does so, do not force it to. Comment on the fact that there must have been a systematic error.
* When choosing values to read of a graph, it is better to take them from the middle part of the curve, as this is where you will have more points per change in y co-ordinate.
* When describing your "plan" in Experiment C, state that the graph you plot will be a straight line through the origin (if this is the case!), of gradient = to an expression which will help you confirm the relationship suggested by the examiner.
* Turning points on graphs require at least 4 points.
* If points near the origin deviate substantially from your line of best fit, point out that for small measurements there is a greater uncertainty.
Experiments Involving Temperature
* Readings should be accurate to fractions of a degree.
* Stir any liquid being heated.
* Insulate the apparatus if possible.
* The thermometer should not be touching the sides of the container it is in, and should be in the middle of the liquid you are measuring the temperature of.
* Precaution: read the thermometer at eye level to avoid parallax error.
* The bulb of the thermometer should be completely submerged.
* Comment on the result obtained being the right order of magnitude.
- Messages
- 1,800
- Reaction score
- 1,800
- Points
- 173
No it's not, but I went through it just in case for my practicals. Additional learning always helps.
- Messages
- 2,884
- Reaction score
- 415
- Points
- 93
it always does!arlery said:
- Messages
- 4,291
- Reaction score
- 6,457
- Points
- 523
thank u so much i wil tell many people abt dix post okayyy.....
- Messages
- 1,800
- Reaction score
- 1,800
- Points
- 173
@AlyHamza I have checked the markschemes and a lot of times they say don't give marks for these errors,hence to be on the safe side I wrote that.
- Messages
- 10
- Reaction score
- -1
- Points
- 3
M/J 07 P31 .. this ques is xpected.
- Messages
- 10
- Reaction score
- -1
- Points
- 3
Sorry ,, forgot to tell the question .. its Q 2
.. its Q 2
- Messages
- 4,291
- Reaction score
- 6,457
- Points
- 523
viewtopic.php?f=26&t=9002 check for physics p34 check dix out....
- Messages
- 626
- Reaction score
- 3,628
- Points
- 253
the uncertnity portion has sm txt missing if u could pls cmplt it?? it would b a great help =)
- Messages
- 626
- Reaction score
- 3,628
- Points
- 253
the examples are missing i find it incomplt :/ could u pls go thru it once
- Messages
- 1,800
- Reaction score
- 1,800
- Points
- 173
The corrections have been made.
Uncertainties
* % Uncertainty =
* When multiplying or dividing quantities, add their % uncertainties together.
* When adding or subtracting quantities, add their absolute errors together, then divide by the result of the addition/subtraction of the measurement, e.g. for
, where
, and
, the absolute errors added = 0.102 mm. Therefore the % uncertainty is:
* If you have to calculate the error in, e.g.
, the absolute error in d must be multiplied by pi and then added to the absolute error in x. The percentage uncertainty is this total error divided by the calculated
and the result multiplied by 100.
* If a measurement is to be raised to a power, then multiply the % uncertainty in the measurement by the power to get the % uncertainty in the overall term.
*If two values, for say, a density are available, calculate the % difference between them. If a value is given by the examiner, then use this as the "correct" value, and calculate the % difference the following way:
where x is your measured value, and c is the examiner's value. If you have obtained two values, then the expression changes:
where x1 and x2 are your measured values, and
is the median of the two, (not necessarily the mean!).
* Compare the % difference with your % uncertainty. Any relationship suggested, such as that the two densities should be equal, can be considered correct if your % difference is less than your % uncertainty. This will gain you marks!
* If your % uncertainties look small, check that you have multiplied by 100!
Uncertainties
* % Uncertainty =
* When multiplying or dividing quantities, add their % uncertainties together.
* When adding or subtracting quantities, add their absolute errors together, then divide by the result of the addition/subtraction of the measurement, e.g. for
* If you have to calculate the error in, e.g.
* If a measurement is to be raised to a power, then multiply the % uncertainty in the measurement by the power to get the % uncertainty in the overall term.
*If two values, for say, a density are available, calculate the % difference between them. If a value is given by the examiner, then use this as the "correct" value, and calculate the % difference the following way:
* Compare the % difference with your % uncertainty. Any relationship suggested, such as that the two densities should be equal, can be considered correct if your % difference is less than your % uncertainty. This will gain you marks!
* If your % uncertainties look small, check that you have multiplied by 100!
- Messages
- 626
- Reaction score
- 3,628
- Points
- 253
thnkx a million =)