help me in this graph...Urgent

[niassu]

plz in Q 1 http://www.xtremepapers.me/CIE/Cambridg ... _qp_62.pdf

draw or tell me which scales are used

 

[CaptainDanger]

For y-axis start frm 40 and take 2 cm = 10 m/g


For x-axis I would go with .0066 or .007 for 1 cm and start form zero....

 

[niassu]

For y-axis start frm 40 and take 2 cm = 10 m/g


For x-axis I would go with .0066 or .007 for 1 cm and start form zero....

i donot understand wht u meant for x-axis do u mean start from zero then leave 1 cm then use 0.007
sorry

 

[CaptainDanger]

No need to say sorry....

Yes you are right, start from 0 and then after 1 cm mark .0066 or .007...

 

[niassu]

No need to say sorry....

Yes you are right, start from 0 and then after 1 cm mark .0066 or .007...

answer this plz
OCT/NOV 2009 3 D
also http://www.xtremepapers.me/CIE/Cambridg ... 9_qp_6.pdf
should the line pass through all points and what scale u prfer

 

[CaptainDanger]

You need to draw the best fit line here.... It may not cross all the points... Leave same number of points on each side of the line you draw and try to go through as many points as you can...

Scale

y-axis
1cm = .5 Ω

x-axis
1cm=.1 m

 

[yousef0074]

i would start the y-axis from 40 and the x-axis from 0.03 where 10 cm on y-axis is 10g and 10 cm on x-axis is 0.01 (1/cm)

 

[CaptainDanger]

10 cm????? It won't fit in there...?

 

[yousef0074]

ohh... sorry dude, i meant 2 cm for 10g on y-axis and 0.01 (1/cm) on x-axis, starting y-axis from 40 and x-axis from 0.03

 

[yousef0074]

and would you please take a look at physics paper 6, october/november 2008 session question 2 part a

any help would be appreciated

 

[CaptainDanger]

Oh okay... AND IGCSE paper? Right?

 

[yousef0074]

yes

 

[CaptainDanger]

I hope I am right...

 

[niassu]

Oh okay... AND IGCSE paper? Right?

plz could u answer this OCT/NOV 2009 3 D
i really appreciate ur cooperation thnx alot

 

[CaptainDanger]

Paper?????

 

[niassu]

http://www.xtremepapers.me/CIE/Cambridg ... 6_qp_6.pdf

 

[CaptainDanger]

Q3 in this paper does not have any d part? Sorry....

 

[niassu]

Q3 in this paper does not have any d part? Sorry....

http://www.xtremepapers.me/CIE/Cambridg ... 9_qp_6.pdf
i know its parallel but need to know is like that

 

[niassu]

also this plz i got my measurements withinthe range but my average still 7.25 while mark sceme is 7.5
http://www.xtremepapers.me/CIE/Cambridg ... _qp_61.pdf

 

[CaptainDanger]

Q3 in this paper does not have any d part? Sorry....

http://www.xtremepapers.me/CIE/Cambridg ... 9_qp_6.pdf
i know its parallel but need to know is like that

Write X there just as the wire is entering the Motor A and Y after the wire leaves it...